At audio frequencies, LC filters were undesirable because of expensive and bulky inductors. Prior to the advent of solid-state active devices, passive RC filters were an audio design option. During the last 30 years, analog active RC filters and digital filters have taken over most low-frequency filter applications. Occasionally, very simple passive RC filters, with four or fewer circuit elements, are used for instructional purposes in laboratory experiments. But they provide limited selectivity. Recently, however, passive RC filters have been revisited to achieve low cost and enhanced selectivity.

RC filters are frequency-sensitive attenuators that supply large pass-band insertion losses (almost 10 dB, including reflection loss), compared to LC filters. The low-pass filter uses cascaded pi sections, while the high-pass filter employs cascaded tee sections.

The filter design procedure is very simple: All resistors have a value that equals the circuit impedance. All capacitors provide a normalized (to source and loaded impedance) reactance of unity at a design reference frequency. Both filters have a nominal reference frequency of 1.2 kHz. The two filters were constructed on vector boards and installed in die-cast aluminum enclosures with input/output BNC panel jacks. Filter testing required a 600-Ω signal generator and a high-impedance meter preceded by a 600-Ω feedthrough termination.

Figure 1 shows an RC low-pass filter schematic. All capacitors are 50-V polypropylene units of 0.22 µF with ±2% tolerance. The resistors are 1/4-W metal film units of 590 Ω with ±1% tolerance. See Table 1 for measured test data.

Figure 2 illustrates the RC high-pass filter schematic. Capacitors are 50-V polypropylene units of 0.22 µF with ±2% tolerance, and resistors are 1/2-W composition units of 620 Ω with ±5% tolerance. Measured test data is shown in Table 2.

Passive RC filters are easy to design at audio frequencies, and they don't require external dc excitation. Evaluation of passive RC low- and high-pass filters reveals response shapes that seem to be monotonic. A relative stop-band rejection in excess of 40 dB was obtained for the equal element filters. Cost savings are possible by using a minimum number of different value components.

Passive RC filters are a design option for high-voltage and high-power applications.

Reprints

Printer-Friendly

Email this Article

RSS

Submit PlanetEE del.icio.us Digg Reddit Newsvine StumbleUpon Netscape Yahoo MyWeb Live Bookmarks Fark  Submit

Font Size

What's This?

1W LED Brightens Solid-State Lighting Designs Development Kit Promises High Quality Headsets And Bluetooth Speakers Diode Arrays Carry DSCC Qualification Eight-Bit MCUs Address Green Issues Data Terminal Eases Mobile Management MLCCs Stand Up To ESD

A New Design Inflection Point Forecasting Industry Growth For 2009 And Beyond EDA Retools To Exploit Multicore Architectures Design And Verification Move Up In Abstraction EDA Retools To Exploit Multicore Architectures A New Design Inflection Point Design And Verification Move Up In Abstraction Challenges Lurk For 22-nm Physical Implementation

1) Transportation Guidelines For Lithium Batteries Get Updated (2033 views today) 2) WHITE PAPER: Liquid-Level Monitoring Using a Pressure Sensor (325 views today) 3) Build A Smart Battery Charger Using A Single-Transistor Circuit (302 views today) 4) 1-A Switching Regulators Operate With 96% Efficiency To Replace Linear Regulators (254 views today) 5) New Power Approaches May Fuel Analog Job Opportunities In Security And Health Applications (143 views today) ALL TOP 20

Reader Comments Notes are all over just pic a book 'filters' take time to study it dont like easy things from other people's brain. Some of the questions here are easy to get along with answeres only if your you keep your brain running. Peace! Abel Kyalo -July 20, 2006 Stop bothering this guy with your school work. Anonymous -January 18, 2006 Stop bothering this guy with your school work. Anonymous -January 18, 2006 We are looking for a filter. It should pass all frequencies upto 60Hz/70hz and should reject freequencies above 100Hz. pls suggest regards, SUNIL JADHAV SUNIL JADHAV -December 09, 2005 We are looking for a filter. It should pass all frequencies upto 50Hz and should reject freequencies above 100Hz. pls suggest regards, SUNIL JADHAV SUNIL JADHAV -December 09, 2005 We are looking for a filter. It should pass all frequencies upto 50Hz and should reject freequencies above 100Hz. pls suggest regards, SUNIL JADHAV SUNIL JADHAV -December 09, 2005 The "R" I was talking about is the representative of the resistor used in the basic diagram of a low pass filter: a Vi connected to a resistor (R) in serie and a capacitor in parallel. Thanks Rui Caldeira -August 10, 2005 Hi I'm trying to make a peak indicator to low frequency. I want to connect it to my mixer headphones output... I checked my mixer impedance which is 374 ohms but I don't know what more to do.(I was planning to connect a led to the Vo) R --/\/\/\---+--- | Vi C = Vo | --------------- Do I have to assume that my R is equal to 374 ohms? Please help me out with this!!! Rui Caldeira -August 10, 2005 Have you the design to complete a passive filter that meets the following critera: The filter is for use in a 600-ohm audio circuit. I need information on the following type of filter: It is to be a low-pass filter. The audio response is to be flat to 12 Khz. From 12 to 20 Khz it is to provide at least 30 dB attenuation. The input level is around 0 dBm. Can you help? P.Burfield -January 27, 2005 I'm looking for a low-pass filter with a cutoff frequency of only 50 Hz. Tell me the price and other details. Thanks Ram prakash -June 25, 2003
POST YOUR COMMENTS HERE Name: Email:
Your Comments: Enter the text from the image below Please refresh the page if you have trouble reading this text.