Certain current-sense amplifiers have to contend with frequent overvoltages. For example, a current-sense amplifier that monitors batterydischarge currents in an automobile must withstand high-voltage "load dump" pulses produced when loads are disconnected from the battery. This causes inductive spikes and overvoltages at the output of the alternator. If these pulses exceed the amplifier's common-mode voltage, the amplifier requires external protection circuitry.

Such a circuit needs only a pair of Zener diodes, a pair of resistors, and another diode (Fig. 1). The common-mode voltage range of the example amplifier (MAX4372) is 0 to 28 V. That's more than sufficient for measuring automotive battery voltages, which vary from 6 to 18 V. Load-dump voltages, however, can reach 35 V and persist for 0.5 seconds, well over the amplifier's 30-V absolute maximum rating for input voltage. Thus, the amplifier needs external protection.

You can avoid additional errors in the input-offset voltage by using different values for input-protection resistors R1 and R2 (2 kΩ and 1 kΩ, respectively), thereby balancing the effect of the amplifier's unequal bias currents. For details on selecting these resistor values, see application note APP3888 (www.maxim-ic.com/appnotes.cfm/an_pk/3888). Zeners Z1 and Z2 have 24-V breakdown voltages, plus sufficient power-dissipation capability to withstand the approximately 11-mA sink currents that flow during a 35-V peak load-dump condition. (The 35-V load-dump voltage minus a 24-V clamp voltage appears across the 1-kΩ series resistor, R2.)

Figure 2 depicts the amplifier output in the presence of 35-V load-dump pulses without D1. With normal battery voltages applied, the 1-V output value is as expected (input VSENSE = 50 mV and gain = 20). When a load-dump voltage appears, the Zeners clamp the input common-mode voltage to 24 V, and the amplifier output makes a few transient excursions before settling down to 0 V.

Because the two Zeners generally have slightly different breakdown voltages, due to part-to-part variations, and different operating currents (Z1 operates at 5.5 mA and Z2 operates at 11 mA), the quantity (VZ1-VZ2) appears as a changing differential sense voltage, which causes the unwanted output transients. You can eliminate these transients by adding D1 in series with either Z1 or Z2. The diode forces VZ1-VZ2 to be positive or negative during a load-dump, which in turn forces the amplifier output to one of the supply rails (VCC or GND), thereby preventing output spikes during an input transient. Connecting the diode in series with Z1 forces the amplifier output to the positive rail (Fig. 3). Connecting the diode in series with Z2 forces the amplifier output to the negative rail.

Reprints

Printer-Friendly

Email this Article

RSS

Submit PlanetEE del.icio.us Digg Reddit Newsvine StumbleUpon Netscape Yahoo MyWeb Live Bookmarks Fark  Submit

Font Size

What's This?

Video Processing Mezzanine Card Basks In Harsh Environments Current-Sense Amp Integrates Reverse-Battery/Load-Dump Protection PoE Modules Ensure Safety, Support High Power Mode Linear Voice Coil Actuators Live Long Battery Charger Dynamically Manages System Load/Charging Small NiMH Charger Speeds Time to Market

In EDA, A Year Of Mergers, Failed And Otherwise 2008 BEST Electronic Design Winners Engineers Rely On Internet For Product Info Rochester Electronics Establishes New Design and Technology Group November 17, 2008 Custom Sources Light Way To 22-nm IC Lithography Software Turns Scopes Into Vector RF Signal Analyzers Couple’s $15 Million Gift Advances Rice Engineering Education

1) Build A Smart Battery Charger Using A Single-Transistor Circuit (264 views today) 2) Ten Top Design Skills For Tough Times (197 views today) 3) Consumer Electronics Series: AMD Live! Home Cinema Platform (188 views today) 4) Easily Convert Decimal Numbers To Their Binary And BCD Formats (163 views today) 5) FPGA Costs Half A Buck (109 views today) ALL TOP 20

Reader Comments NONE Anonymous -October 02, 2008
POST YOUR COMMENTS HERE Name: Email:
Your Comments: Enter the text from the image below Please refresh the page if you have trouble reading this text.